Once it's dry, you can reassemble your Clarisonic and enjoy soft, clean skin once again! If you soaked the brush in vinegar, you may also want to wash the it with dish soap to get rid of the smell. Plan on disinfecting your Clarisonic roughly once a month to keep it in good working condition.
Laura Martin Licensed Cosmetologist. Laura Martin. Yes, the Clarisonic is waterproof. It is fine to use it and store it in your shower. Yes No.
Not Helpful 0 Helpful 0. Detach it from the brush and scrub it with soap and water. Then use alcohol to remove any remaining scum. You can use it up to twice a day. You shouldn't be washing your face more often than that. Unlock the head by pushing in and turning counterclockwise. Attach the new head by pushing and turning clockwise until it locks. Include your email address to get a message when this question is answered.
Frequent cleanings can prolong the lifespan of your Clarisonic brush head, but it's still a good idea to change it out for a new one about every three months.
Helpful 0 Not Helpful 0. Store your Clarisonic with the removable brush cap on minimize exposure to bacteria. Also be sure to store your Clarisonic in a space that is free of moisture. Questionable odors or a slick coating on dry bristles may be evidence of mold growth.
Should you encounter either of these things, opt for a thorough disinfecting. Don't share your Clarisonic brush head with anyone else. This can transfer bacteria to your skin, nullifying the benefits of the brush and increasing your risk of breakouts or infection. Other wikiHows How to. How to. Skincare Specialist. Expert Interview. More References 9. About this article. Co-authored by:. Squirt a few drops of soap on your fingers or a toothbrush and scrub the bristles and crevices first.
Don't worry about harming the brush head — the bristles are built to take some abuse. Rinse with warm water and repeat with the handle. Both Prather and Shamban say any soap will do — even dish soap. That said, Prather recommends avoiding harsh detergents and chemicals that you would not want on your skin or face. Furthermore, Clarisonic advises against using abrasive cleaners or chemicals.
If you prefer, you can use a hand soap or facial cleanser to wash the brush. Massage the soap into the bristles. You should massage the soap into the brush for 30 seconds to 1 minute to ensure that it is fully clean. If the brush head seems particularly dirty, you may want to use a clean toothbrush to scrub the soap into the bristles and the surface of the brush head.
Run the brush head under water. Rinse the brush head under warm water to remove all of the dirt, oil, and soapy residue. Set the brush head out to air dry. When the brush head is clean, allow it to sit out to air dry. You can replace it on the handle and let it dry like that, or leave the brush on a towel by itself to finish drying. The cap has holes in it to ventilate the brush head so air can still reach it to help it dry.
You should remove your brush head and give it a thorough cleaning at least once a week. However, be sure to rinse the brush head well after each use. Even with proper cleaning, you should replace your Clarisonic brush heads every three months. Method 3. Mix the baking soda and hydrogen peroxide. Add 2 parts baking soda to 1 part hydrogen peroxide in a small dish. Stir the two together well until a paste with a yogurt-like consistency forms.
If the mixture is too liquidy, stir in more baking soda. Use a solution of hydrogen peroxide once a week. You can soak the brush head in hydrogen peroxide for up to an hour once a week to clean any bacteria or residue. Allow the head to air dry and store it away from moisture. You should also replace the brush head every three months.
Add some lemon juice into the mixture. After the baking soda and hydrogen peroxide mixture has reached the right consistency, cut two to three slices off of a lemon. Squeeze the juice from the slices into the mixture, and stir well to combine. Spin the brush head in the mixture for a minute. With the brush head attached to the Clarisonic handle, turn on the device. Allow the head to spin in the baking soda, hydrogen peroxide, and lemon juice mixture for 30 seconds to 1 minute so the bristles are thoroughly coated.
Swish it around the mixture for 30 seconds, and then rub it against your palm to work the cleanser into the bristles. Avoid any cleansers with microbeads or rough particles.
You don't replace your brushes every three months. Robb says it isn't the bacteria you need to get rid of, it's more about the efficiency of the machine. Over time the bristles begin to clump together, so a replacement is required! Go ahead and push that button again to give your neck and collarbone a good antiaging scrub. Home Beauty Stop, No! Stop, No! Save Pin FB More. Credit: Getty Images. All rights reserved.
0コメント